Just How To Replace A Bathtub (For Newbies).
Just How To Replace A Bathtub (For Newbies).
Blog Article
The author is making a number of good points relating to Tools You Need to Install a New Bathtub in general in this content followed below.
Mounting a bathtub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a new one is likewise a reasonably difficult job. If the old bathtub is conveniently accessible, the project can move immediately; if you have to open up a wall to remove the old tub as well as place the brand-new bathtub, the task is a lot harder. In either instance, the task is within a home handyman's skills, although you will need an assistant to leave the old bathtub and also embeded in the brand-new one. See to it you have actually certified on your own for the work and also are comfortable attempting it. Rather than hiring a service provider to take control of a halfway-completed task, it is far better to take into consideration using one prior to you start. Possibilities are you might require an expert plumber to make tube connections.
This short article will assist you mount a brand-new bath tub in your washroom if you have actually currently purchased a new tub and don't need to transform the setup of your previous water pipelines.
Your devices and also product list must make up the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the water. After doing so, activate the faucets to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be quite troublesome due to the limited accessibility that is typically the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the taps. Have a towel prepared for the remaining water that will come from the pipelines. When the supply pipes have actually been eliminated, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before going on to fit the new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the installing opening in the bath/basin guaranteeing that the washing machines are in location in between the tap and also the sink. Secure the faucet in place with the maker provided backnut. When the faucet is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap ports. The previous type must be connected to the tap finishes first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Using the two wood boards under its feet, place the tub in the called for position. The wooden boards are practical in evenly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by checking the level and also readjusting the feet on the bathtub until the spirit level checks out degree.
To set up faucets, fit all-time low of the furthest flexible tap port to the ideal supply pipe by making a compression join; then do the exact same for the various other tap.
Turn on the water and also check all joints and new pipework for leakages as well as tighten them if essential. Load the bathtub and also inspect the overflow electrical outlet as well as the regular electrical outlet for leakages.
Ultimately, deal with the bath paneling as explained in the maker's user's manual. Tiling and also sealing around the bathtub ought to wait up until the bath tub has actually been used at least once as this will settle it into its final setting.
Planning for the Installment
Firstly, the supporting frame supplied with the bath must be fitted (if needed) according to the supplier's guidelines. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be fitted in its final placement.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to break a rigid seal, causing the water to pass through the wall surface in between the bath and the tiling, leading to difficulties with wetness as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components and also fittings. They are sold in tubes and cartridges, and also can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of drenched paper or soft rope. Keep in mind to always load the tub with water before securing, to enable the movement experienced when the bathtub remains in use. The sealer can break rather very early if you do not take into consideration this motion before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise quickly available on the marketplace. It is advisable to fit the ceramic tiles using waterproof or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our part on How to Install a Bathtub. Thank you so much for spending some time to read our piece of content. Feel free to set aside a second to promote this blog post if you liked it. I am grateful for your time. Kindly come by our site back soon.
Estimate Free Report this page